undefined

undefined

How to Specify Cosmetic Surfaces on CNC Drawings

Specify cosmetic surfaces on CNC drawings with clear finish zones, acceptable marks, masking and inspection notes. Adapt a practical front-panel example.


Mark the faces people will see after assembly, specify the finished appearance on those faces, and agree on how it will be inspected. Then mark any threads, fits or contact areas that must be protected during finishing. “Black anodize, no scratches” is a finish request, but it does not tell the supplier where a rack mark can go or how to judge a borderline scratch.

Consider a machined aluminum control panel. A clamp mark on the back may be harmless. The same mark beside the display may make the part unacceptable, even when every dimension is correct. You do not need to finish both faces to the same visual standard. You do need to say which face matters.

1. Mark the faces in their installed orientation

Use a drawing view or a revision-controlled annotated image. Point to the surfaces themselves rather than relying on a note that says “visible areas.” Include edges and chamfers if they remain visible after assembly.

  • Zone A — front face: The face around the display cutout, including the visible chamfer. This is the primary appearance surface.
  • Zone B — side edge: Visible from the side once installed. Give it its own acceptance criteria if it does not need the same appearance as the front.
  • Hidden rear: Specify where normal fixture or rack contact is allowed, outside mounting and electrical contact areas. Hidden does not mean dimensionally unrestricted.

A and B are drawing labels, not universal quality grades. Define them in the drawing legend or reference an agreed appearance specification by revision.

2. Specify the appearance separately from the process

A finish name describes the route, not everything the buyer will see. For a brushed face, show the grain direction with an arrow. For a blasted and anodized face, state the appearance the final finish should match. If color, texture or gloss is critical, identify an approved finished part or representative sample and agree on what variation is acceptable. An image can help communicate intent, but do not use an uncalibrated photo as the sole color reference.

Ra is not a scratch or color limit. Use a roughness callout where a feature needs one. Use separate appearance criteria for scratches, dents, directional marks and color variation. If the finish route is still open, review the surface finishing options before freezing the drawing.

3. Agree on what passes, and how to check it

Decide which marks are allowed in each zone and what counts as a reject. When a verbal description leaves room for disagreement, agree on measurable limits or approve a boundary sample showing the worst appearance you will accept. Define the inspection lighting, viewing distance, angle and whether magnification is used when those conditions affect the decision. Inspect after the final finish and before packing.

For a prototype that will lead to repeat orders, keep the approved sample or appearance record with the drawing revision. Where the batch has multiple adjacent visible parts, tell the supplier which ones must be judged together. Use the quality management page to discuss what inspection evidence should accompany the quote.

4. Keep appearance from compromising fit

Call out any features that must remain masked, uncoated, or otherwise protected. On the control panel, that might be a specified grounding pad or a locating bore. Mark the boundary, say which dimensions apply in the finished condition, and agree on the inspection method for critical features. Do not leave the supplier to infer masking from a general finish note.

Example drawing note: a black anodized front panel

Adapt this example to the part and attach the referenced appearance specification to the RFQ. It is not a default acceptance standard.

  1. Bead blast and black anodize as specified. Zone A includes the front face and marked display chamfer. Inspect Zone A against the approved finished sample and the agreed visual inspection conditions. No rack contact in Zone A.
  2. Inspect the marked side edge as Zone B against its agreed criteria. Rack contact is permitted only in the indicated rear area, clear of mounting and electrical contact features.
  3. Mask the marked grounding pad. The locating bore must meet the drawing limits in the finished condition; confirm the inspection method at quotation.
  4. After inspection, separate panels in packing so their visible faces cannot rub against other parts or hardware.

Before sending the RFQ, attach the CAD file, marked drawing, any sample reference, the finished dimensions that matter, and the order quantity. If the appearance criteria are not final, identify what still needs sample approval instead of letting each supplier quote a different interpretation.

Get a Quote